When a furnace stops producing heat on a cold night, or an air conditioner runs all afternoon without bringing the temperature down, that call needs to reach someone who can actually help. We handle heating and cooling repair, service, and installation for homes and businesses across Conyers and Rockdale County. The work covers the full range: AC repair, furnace repair, heat pump service, system replacement, ductwork, thermostats, indoor air quality, seasonal maintenance, and emergency calls when the system is completely down.
Conyers is a town where a lot of the housing stock carries systems that have been running for years without a proper look. Older equipment, additions that the ductwork never quite reached, and units that have been repaired once or twice already make up a good share of the calls we get here. We scope the job on the phone before anything is scheduled, and we confirm the price before the visit begins.
Call (943) 256-2995 to get started, and we will work out what your system needs.
HVAC pricing moves based on three things: what the fault turns out to be, what has to be accessed to fix it, and whether a repair or a replacement is the right answer for that particular system. A diagnostic call on a single unit is scoped differently from a full furnace-and-AC replacement on a two-story home. Neither of those has a fixed number until the system is described and the visit is scoped.
What does not move is when you find out. The rate is confirmed on the call before anything is scheduled. No-pressure estimates, priced up front, so there is no ambiguity about what the visit covers going in. If something changes on-site, that conversation happens before any additional work starts. Nothing gets added to the job without your agreement.
If you are not sure whether the situation calls for a repair or a replacement, that is a reasonable question to raise on the call. The person who answers knows the trade and can help you work through what the system is doing and what the options are likely to look like.
The visit gets arranged on the phone. You describe what the system is doing, the job gets scoped, and the price is confirmed before anything is booked. From there, the appointment is set and you know what to expect before the technician arrives.
For emergency calls, when there is no heat, no cooling, or the system has stopped responding entirely, those are handled every day within our published hours of 8:30 AM to 8:00 PM. When you call, someone who knows the trade answers and starts working through the situation on the phone.
We also work around tenants and occupied commercial spaces. A rental unit that needs to stay livable, a retail space that cannot close for a full day, an office building that has to keep running through the visit. The scope and timing get worked out on the call so the visit fits the property's situation. We keep you posted from the first call until your system's running again.
Schedule it. We fix it. You're comfortable.
An older thermostat that is reading temperature incorrectly, failing to communicate with the air handler, or simply not responding reliably can make a perfectly functional system behave as though it is broken. Short cycling, continuous running, or a system that ignores the temperature setting are all symptoms that point toward the thermostat before the equipment itself.
A modern programmable or smart control does things an older unit cannot. It tracks run patterns, lets you set schedules by the day, and gives you visibility into how the system is actually performing over time. Unusual run patterns, like a system that is running longer than it used to on a mild day, show up in the data before they turn into a repair call.
Thermostat replacement is also worth considering on its own when a system is otherwise running well. Replacing an aging control is a lower-cost step that can resolve comfort complaints and improve efficiency before a larger job becomes necessary.
We take over work started by somebody else. A repair that did not hold, a system that was serviced recently but is already showing the same problem, or a job that was started and not completed. These calls come in regularly, and the process is the same as any other: look at what is there, figure out what it actually needs, and give you the options before any work begins.
A second opinion is always a reasonable call before committing to a large repair or a full replacement. If another technician has told you the system needs a major component or a full changeout, and you want a second look before you decide, call and describe the situation. We will scope what the visit would cover and confirm the price before anything is arranged.
What we do not do is quote parts before the system is checked. A diagnosis that starts with the answer and works backward is how repair calls become expensive guesses. The system gets looked at first, and the options come from what is actually found. The range of work covered is explained on our full list of heating and cooling services.
For residential and commercial HVAC work alike, the job types below cover the situations we see most often in this area. Each one starts with a symptom or a situation, and the visit is scoped from there.
A home that has never had central air, or one where the existing system has reached the end of its useful life, is a candidate for a full installation. Sizing the new equipment correctly for the space matters more than most people expect. An oversized unit short cycles and leaves humidity behind. An undersized one runs continuously and still falls short on the hottest days. We work through the load before anything is ordered, and the installation covers the air handler, the outdoor unit, and the connections to the existing ductwork or new duct runs if the space requires them.
Homes with boiler-based radiant heating have a different set of needs from forced-air systems. A boiler that is not reaching temperature, a zone that has gone cold, or a system that is making noise it did not make before all point toward specific components. We service boilers and hydronic heating systems, and the diagnostic process covers the heat exchanger, the circulator pump, the zone controls, and the expansion tank. Radiant heat is a different kind of comfort, and the system that delivers it deserves a technician who understands how it works.
A heat pump that blows cool air in heating mode, trips into emergency heat on mild days, or runs continuously without warming the space is showing signs that need a proper look. Defrost cycle failures are a common cause of heating problems in this region's winters. When the defrost cycle does not complete, ice builds on the outdoor coil and the system loses its ability to extract heat from the air. A refrigerant charge issue or a reversing valve fault can produce similar symptoms. The diagnostic starts with what the system is doing, not with a parts list.
A furnace that starts and then shuts off before completing a heating cycle, or one that attempts to light and fails repeatedly, is usually dealing with an ignition or flame sensor problem. A dirty or failing flame sensor is one of the more common furnace faults, and it is also one of the more straightforward to address once the system is properly diagnosed. Ignition failures that are left to repeat put additional wear on the control board and the gas valve, so this is not a situation to monitor and wait on.
Short cycling, where the system starts and stops repeatedly without completing a full run, puts mechanical stress on the equipment and leaves the space uncomfortable. The cause varies. A pressure switch fault, a tripped high-limit switch, an airflow restriction through a clogged filter or blocked return, or a refrigerant charge issue can all produce the same symptom from different directions. Energy-efficiency suffers as well, because a system that cannot complete its cycle is running its startup sequence over and over. The diagnostic looks at the whole system rather than assuming the cause before the visit begins.
We serve Conyers and the surrounding Rockdale County communities, including Milstead, Lakeview Estates, Oxford, Porterdale, and Lithonia. Whether the property is a home, a rental unit, or a commercial space, the process is the same: a call, a conversation about what the system is doing, and a price confirmed before the visit is arranged.
If you are not sure whether your address falls within our service area, call (943) 256-2995 and we will confirm it on the spot. We are available every day from 8:30 AM to 8:00 PM.
Yes. We serve Milstead, Lakeview Estates, Oxford, Porterdale, and Lithonia, as well as the broader Rockdale County area.
If you are not certain whether your address is covered, call (943) 256-2995 and we will confirm it before anything is scheduled.
Older homes in this area often have systems that have been running for years without a full diagnostic check, and the calls that come in most often reflect that. Furnace ignition failures, AC units that have lost refrigerant charge over time, and ductwork that leaks conditioned air into unconditioned spaces are among the most frequent. Heat pump defrost faults also come up regularly in the colder months. A maintenance visit before each season is the most straightforward way to catch these before they become a no-heat or no-cool situation.
Describe what the system is doing, or not doing, as specifically as you can. Whether the unit is running but not heating or cooling, making a noise it did not make before, cycling on and off repeatedly, or simply not responding to the thermostat, that information helps scope the visit correctly before anyone arrives. The person who answers knows the trade and will ask the right follow-up questions to get the job set up properly.
It depends on the scope of the work and where the equipment is located. Routine service and minor repairs can often be completed without disrupting operations. A full system replacement or significant ductwork work may require a portion of the space to be taken offline temporarily. We discuss the impact with you before the visit is scheduled so you can plan accordingly.
Describe what the property is doing and we will work out what the visit should cover. We take calls every day from 8:30 AM to 8:00 PM.
Call (943) 256-2995 and a few questions about the system are all it takes to get started.
Plain questions. Honest diagnosis. Clear options.
Neighboring areas in range: Lakeview Estates, Redan, Loganville, Social Circle. There is more on our full service area.
We handle the full range of heating and cooling work across Conyers and Rockdale County, from a seasonal tune-up to a full system replacement. The table below lays out what each service covers, who it fits best, and what is worth knowing before you call. Every job starts the same way: a conversation on the phone, a price confirmed before anything is scheduled, and a visit focused on what the system actually needs.
| Service | Scope of Work | Best Suited For | Helpful Details |
|---|---|---|---|
| Full System Installation & ReplacementMost Popular |
| Homeowners and building operators whose system is past the point where another repair makes financial sense | An oversized unit short-cycles and leaves humidity in the air. An undersized one runs constantly and never catches up. Sizing the replacement correctly is the first conversation we have. |
| Thermostat & Smart Controls |
| Households where the system behaves erratically or where better temperature visibility is a priority | A thermostat that is not reading temperature correctly can make a fully functional system look like it has a serious problem. Diagnosis comes before any replacement is quoted. |
| Seasonal Maintenance & Tune-Ups |
| Homeowners who want to catch small problems before they become an emergency on the worst possible day | Both the spring cooling tune-up and the fall heating tune-up end with the system tested and readings checked, so you know the system is ready for the season ahead. |
Call us at (943) 256-2995 to talk through what your system needs and get a price confirmed before anything is scheduled.
(943) 256-2995